7 Top Related Articles About Plumbing Today

In most areas propane gas is equally as expensive or more expensive than electricity. Quick Recovery Rate: a gas water heater can recover at 3-4 times the rate of a comparable electric device. An average electric tank recovers 14 gallons/hr, compared to 50 gallons/hr for a gas model. Thus, a gas heater allows you to get more hot water from a smaller size tank, which is more energy efficient. A smaller size tank can also save useful space in your house. Lower Device Cost on High Efficiency Models: on average, a standard gas storage heater can be a few hundred dollars more expensive than a standard electric model. However, high efficiency electric models (heat pump) offer a limited selection and are significantly more expensive than high-efficiency gas storage tanks ($500-1,000 price difference) Hot Water During a Power Outage: if power goes out, you will still enjoy hot water delivered by your gas heater (this is true of models that use a pilot lights, as opposed to electric ignition). Important Considerations for a Gas Hot Water Heater If you are leaning towards installing a gas powered water heater, there are a few things you should be aware of: Expensive retrofit installation: if your house is not fitted with a gas line, installing one can cost thousands of dollars. A gas water heater (both tank and tankless) requires venting and gas pipe lines.

https://stopwaterheaterleaking.com/why-gas-water-heaters-are-a-good-idea/

Consequently, you gain useful flooring or storage room space. By contrast, a storage water heater is very bulky; a 40-60 gallon tank measures on average Gordontheplumber.com Elmhurst Illinois 60126 60″ tall and 24″ wide (most of them are installed on the floor). Cleaner Water: traditional water heating units could build up corrosion and scale inside the storage tank, contaminating the water stored in it. This is why, you sometimes see rusty water coming out of your faucet or shower. By contrast, you will not have this issue with a tankless device; your water will always be fresh and clean. Disadvantages of a Tankless Hot Water Heater As with any device, a tanless water heater has its own set of disadvantages, that may not make it the right option for every household. Initial High Cost: The biggest drawback to switching to a tankless water heating systems is that the purchase and setup prices are dramatically higher than what you would pay for a storage model. The average cost of a tankless unit together with installation can run $2,500-4,000 (a large portion of the cost goes to expensive installation). By comparison, you can purchase and install a 40-60 gallon storage tank for $800-1,500. The price difference is the primary reason why most homeowners stay away from tankless heaters. Limited Water Output: a typical tankless device usually supplies enough hot water to only one location.

https://stopwaterheaterleaking.com/switch-to-a-tankless-water-heater-why-its-a-good-idea-and-why-its-a-bad-idea/

The cost of installing a tankless water heater depends on several factors. The type comes first. A tankless water heater is an umbrella term that refers to units that don’t use tanks. As such, let’s split them to their different models. The major difference boils down to the mode of power. The electric, natural gas, and propane gas-powered water heaters are the most common. Electric tankless water heaters are cheaper than their gas-powered counterparts. Second, the cost of installing a tankless water heater varies with the size of the unit. Needless to say, the best water heater for a building is the one that meets all the hot water needs. Unlike traditional water heaters, tankless units don’t feature gallon capacity size. Consumers use the units’ flow rate to determine the water heater that fits their needs.

https://tankless.best/blog/tankless-water-heater-installation-costs/

A washing machine pipes tail piece must be at least 18" but no more than 30". F. is the p-trap, a washing machine pipes p-trap must be installed above the floor, at least 6" above but not more than 18" above. G. is the trap arm, a 2" p-traps trap arm must be no longer than 60", have at least ¼" per foot of grade, and have only horizontal off sets. H. is the horizontal drain this fixture is joined to. It will be below the floor. Note the combination of the 2" wye and the 2" 45 degree elbow.

https://plumbingcodestuff.tumblr.com/post/147992217763

For the most part getting them out is a relatively straight-forward task, but installing the new ones can be tricky at times. You have to drop the springs into a small recess inside the faucet followed by the rubber seat which also has to sit over the spring and into the recess. Often if there’s water sitting in the faucet, the rubber seat ends up floating up and out of the recess. A good tip is to remove all the sitting water via a sponge or straw so this problem is avoided.I usually, will thread the rubber seat followed by the spring onto a thin blade screwdriver and use it as a guide to lower them into the recess inside the faucet. This has been the way I’ve been doing it ever since I can recall, but recently I found this tool in one of my supplier’s catalogs called a Purge-N-Set tool for seats and springs. Needless to say, besides being a tool geek and curious I had to order one and check it out. Well, I’m happy to say it works really well and for those of you who are having trouble removing and re-installing seats and springs in your Delta faucets, you might want to check it out. You can purchase a Purge-N-Set tool at few online retailers and if you want to see it in action check out the video below where I demonstrate just how it performs. As always if you have any questions on Delta faucet repairs, you can e-mail me at info@bobsplumbingvideos.com. You’ll also find me on Face-Book, Twitter.

http://www.bobsplumbingvideos.com/delta-faucets-delta-repairs-purge-n-set-tool/

You may also be interested to read

Posted in